STABLOAD – Program Help
STABLOAD is a loading program (cargo calculator) used to prepare and verify a ship’s loading condition, including stability, trim, and longitudinal strength. The program interface consists of the main menu, result windows, and a status bar with the most important parameters.
1. Main screen elements
Main menu
The menu is located at the top of the program window and contains commands for data input, running calculation functions, and displaying results.
Calculation mode: Port condition / Seagoing condition
The Port condition / Seagoing condition drop-down list is used to select allowable loads and criteria depending on the operating conditions:
- Port condition – for checking intermediate states in port (e.g. during loading/unloading),
- Seagoing condition – for preparing the departure and arrival condition and assessing seagoing limits.
Status bar
At the bottom of the screen the program displays basic information about the current loading condition, including stability parameters, draughts, trim, and messages such as Stability OK or Long. Strength OK.
The Reserve of DWT parameter shows how much additional cargo can still be loaded up to the permissible draught so as not to exceed the maximum deadweight (DWT) resulting from draught limitations.
2. Windows visible on the main screen
The main screen is organized into a set of windows presenting input data and calculation results. Typical windows visible in the main view are described below.
Weight specification
A summary of weights in the main groups (e.g. cargo, ballast, consumables, stores, ice, deadweight).
This window also shows selected center-of-gravity position parameters
(e.g. LCG, TCG, VCG) and summary data.
Stability tabs: Stability / Hydrostatics
The Stability window contains two tabs:
- Stability – presents compliance with stability criteria (e.g. IMO) and compares required and actual values (including GM, GZ, areas under the GZ curve, and characteristic angles).
- Hydrostatics – presents detailed hydrostatic and geometric parameters of the current condition.
Hydrostatics tab – key items
- Displacement – displacement,
- LCG, LCF, LCB – longitudinal positions of the center of gravity, center of flotation, and center of buoyancy,
- Trim and Trim Moment – trim and trimming moment,
- Draughts – draughts, including at the center of flotation (LCF), midship, aft (TA), and fore (TF),
- VCG – vertical center of gravity,
- Free surface correction (GG') – free surface correction,
- KM, GM, Corrected GM – transverse stability parameters,
- Density of seawater – seawater density used for calculations.
Drafts and trim
A graphical presentation of the ship’s profile with cargo holds and the current draught and trim parameters. This window helps quickly assess whether the loading condition meets operational assumptions and whether the draughts are within permissible limits.
Longitudinal Strength Curves
Longitudinal strength plots along the ship’s length (as a function of frames/positions), including:
- weight distribution (Weight),
- buoyancy distribution (Displacement),
- load distribution (Load),
- shear force (Shear Force) and allowable values,
- bending moment (Bending Moment) and allowable values.
This window is essential to confirm that the vessel meets strength limits in the selected Port condition or Seagoing condition.
GZ Curve
The righting-arm GZ curve as a function of heel angle. It allows assessment of the stability curve shape and verification of requirements (e.g. areas, GZ values, angles).
Critical VCG Curve
A plot showing allowable/limiting VCG values as a function of displacement or mass. It helps assess the safety margin relative to the critical vertical center of gravity.
List (cross section)
A graphical presentation of list (heel) and the ship’s position relative to the centerline. It helps assess whether the ship is listing to port or starboard and how large the list is.
Ballast Tanks (tank view)
A view of the ballast tank arrangement together with their filling levels. This window allows a quick check of ballast configuration and helps identify asymmetry.
Longitudinal Strength (summary)
A summary window showing utilization of allowable longitudinal strength limits, often in bar charts presenting the percentage use of shear force and bending moment limits.
3. Data input windows
Stores
The Stores menu allows entry of crew and provisions weights.
For each item, the weight (Weight) and center-of-gravity positions (LCG, VCG) are provided.
Typical buttons in table windows: Edit, Load..., Export..., Print.
Tanks
The Tanks menu allows entry of ship consumables (e.g. fuel, oils, lubricants, sewage, fresh water). Each tank is described by, among others:
Weight– mass in the tank,LCG,TCG,VCG– center-of-gravity positions,% FullandUllage– filling level / empty space,Density– liquid density,FSM– free surface moment (if applicable),Destination– type of medium (e.g. Fuel oil, Diesel oil, Lubric oil).
Ballast Tanks
The Ballast menu allows loading and editing ballast in ballast tanks. The table layout is similar to the Tanks window (mass, LCG/TCG/VCG, %Full, ullage, density, FSM).
Cargo
The Cargo menu is used to enter cargo in cargo holds. For each hold, the following are provided, among others:
Weight– cargo weight,LCG,VCG– center-of-gravity positions,% Full,Ullage– filling level / empty space,Density– cargo density,- information about the cargo type (e.g. Grain trimmed).
4. Draught Survey window
The Draught Survey window is used to estimate cargo masses and displacement based on draught readings (on port and starboard sides) and specified corrections and deductions.
Input data
- draughts: Aft, Mid, Fore for Port and Starboard,
- seawater density,
- deductions, e.g. fuel, diesel, oils, fresh water, ballast, sundries, etc.,
- light ship mass (Light ship) and optional additional items (Miscellaneous).
Results
- mean draught and MMM draught,
- trim and LCF,
- displacement with corrections (trim and density),
- Actual Displacement and calculated cargo mass (Cargo).
5. Program menu description
| Menu | Function |
|---|---|
| Stores | Enter the weight of the crew and provisions. |
| Tanks | Enter ship consumables such as fuel, oils, lubricants, sewage, fresh water, etc. |
| Ballast | Load or edit ballast in ballast tanks. |
| Cargo | Load or edit cargo (holds, masses, cargo distribution). |
| Results | Display all results presented in the on-screen windows (summaries and reports). |
| Options | Enter voyage information, set seawater density, and enable icing options. |
| Sequence Simulation | Perform the loading sequence simulation (stage-by-stage). A detailed description of running the sequence in STABLOAD is available in: Simulation.html. |
6. Recommended workflow
- Enter input data in the relevant tabs: Stores, Tanks, Ballast, and Cargo.
- In the Options tab, set voyage parameters, seawater density, and—if required—icing conditions.
- Select the appropriate calculation mode: Port condition or Seagoing condition.
- Check results in the stability, draught/trim, and longitudinal strength windows. The stability, strength, and deadweight reserve summary is displayed in the bottom status bar and marked in green (within limits) or red (exceeding allowable limits).
- Monitor the Reserve of DWT value to avoid exceeding permissible draught and ship deadweight.
- If you are preparing a port loading plan, use Port condition. After the plan is prepared, you can run a loading simulation using Sequence Simulation, according to the instructions in Simulation.html.